@FATeknollogee said in How to install SuiteCRM 7.8.3 on Fedora 25 Minimal:

@JaredBusch Ha, I hear ya!

SSL instructions updated.

@travisdh1 said in Install Nextcloud 11.03 on Fedora 25 Minimal:

@dashrender said in Install Nextcloud 11.03 on Fedora 25 Minimal:

@travisdh1 said in Install Nextcloud 11.03 on Fedora 25 Minimal:

@wirestyle22 said in Install Nextcloud 11.03 on Fedora 25 Minimal:

@travisdh1 said in Install Nextcloud 11.03 on Fedora 25 Minimal:

@wrx7m said in Install Nextcloud 11.03 on Fedora 25 Minimal:

@jaredbusch Thanks for the steps. Do you know if you are able to dynamically expand the block storage?

Use LVM with it, doesn't matter weather it's dynamically enabled by Vultr or not, it just is.

I actually didn't know LVM would dynamically allocate it in this situation. Interesting.

Just stop and think about it for a minute and I think you'd get it.

Need to add space, plug in a block device and expand the LV. Need to remove a block device, that's just fine as well (just be sure the VG has enough space to hold all the data after that block device is removed.)

learning question here - when you remove a block device from a VG, does LVM move the data as part of the process of removing the block device?

Yes, so long as there is enough storage space left in the VG, it will move it off the device being removed. Disclaimer: I haven't actually tested this in years.

Interesting. Thanks

@JaredBusch said in How to Install Fedora 25 Minimal:

@black3dynamite said in How to Install Fedora 25 Minimal:

Unlike installing Linux Integration Services, Hot-Add support is not enabled by default after installing hyperv-daemons.

Create a file /etc/udev/rules.d/100-balloon.rules. You may use any other desired name for the file.

Add the following content to the file: SUBSYSTEM=="memory", ACTION=="add", ATTR{state}="online"

Reboot the system to enable Hot-Add support.

See Note 8 on Supported CentOS and Red Hat Enterprise Linux virtual machines on Hyper-V

You mean for dynamic memory to work?

Yes, dynamic memory for ballooning and hot-add.

@scottalanmiller said in Upgrading the FreePBX firmware:

@dashrender said in Upgrading the FreePBX firmware:

@scottalanmiller said in Upgrading the FreePBX firmware:

@aaronstuder said in Upgrading the FreePBX firmware:

@scottalanmiller I assume @WLS-ITGuy means from FreePBX 13

We didn't upgrade from 13, we did a clean slate build.

So was this for a new install, or for a previous customer? If previous, how did you migrate all of your settings over?

We did it on beta, so it was for internal. Wouldn't do that to outside customers.

PBX are really easy to migrate by hand, no need to bring cruft over. IF you have hundreds of users and complex IVRs, yeah that can be a pain. For a typical SMB, how long does a manual migration take, an hour? And if you are cleaning up craft as you go, pruning extensions, it can be a break even on time.

Probably more like 10 mins, ammaright?

@JaredBusch said in ONLYOFFICE NextCloud Integration Documentation failure.:

@travisdh1 said in ONLYOFFICE NextCloud Integration Documentation failure.:

@scottalanmiller said in ONLYOFFICE NextCloud Integration Documentation failure.:

@travisdh1 said in ONLYOFFICE NextCloud Integration Documentation failure.:

Pulled a screenshot, but didn't get things setup in the home lab yet.

You should upload a picture. Whatever Google stuff you have here doesn't work.

Huh, it's showing up fine for me. Anyone else not seeing the screenshot?

This is not the first time I have called you out on this. FFS, last time I told you to just copy past from clipboard.

That hadn't worked for me once and I got into that old bad habit again, dagnabit.

Thank you, this ia very useful

@msff-amman-Itofficer

Sorry, all working 100%

Thank you very much

I should sleep now, its way too late thus making those small mistakes

@scottalanmiller said in Installing Wordpress on CentOS 7 Minimal:

@BRRABill said in Installing Wordpress on CentOS 7 Minimal:

@JaredBusch said in Installing Wordpress on CentOS 7 Minimal:

@BRRABill said in Installing Wordpress on CentOS 7 Minimal:

Going back through this today.

What did we ever decide on PHP 5.X versus 7.X

Since WordPress seems to be recommending the move to 7.X, is it reasonable and desired to install that instead? Even if it is not in the official repositories? (I am, just asking for future reference for others.)

I would install this on Fedora today. If you want to be on CentOS 7, then install the Remi repo and enable the PHP 7.1 repo.

That's two votes for Fedora,then. I know @scottalanmiller is also a fan.

My install guide is written for Fedora :)

How are you getting logs into Elastic Stack or whatever you're using now?

@brianlittlejohn said in Outbound call routing with FreePBX 13:

Is it best to setup a second route for e911 usage?

I always do. Because then I can mark the route as such.

@JaredBusch I see that now. I'm not making plans to make any kind of changes with Asterisk's behavior. I was simply geeking out on the questions of why and how. :)

Justy a note, you need to create an OpenCNAM account and fund it if you do not have one.
https://www.opencnam.com/register

I recommend OpenCNAM because it is generally cheaper than your carrier CID charges.
If you recall from the VoIP.ms setup, they charge $0.008 per lookup.

OpenCNAM is half that at $0.0039 per lookup. https://www.opencnam.com/pricing

Often sales people and management will ask, "How do I check my voicemail from outside?" I always recommend that they enable voicemail to email, but for those that want it, you can set up a silent option in the IVR.

What I mean by silent option is that you will add another option to the IVR, but you will not announce that option in the recorded audio.

Add another entry and choose the Destination category of Feature Code Admin and then select Dial Voicemail <*98>

It should be noted, that when you create a new extension, FreePBX will create user conference rooms automatically if you create a new User Manager user at the same time.

Following up on this way too many weeks later...

Sorry about that...

With VoIP.ms and PJSIP, you also need to go to the advanced tab and change the default expiration time from 3600 to 120.

I have not tested this with other providers yet as it would be disruptive to a client.
When I have time I will setup a backup provider and change my extension to use that normally and see how things go. The problem is that with a not very used system, it will still reregister every hour, so to catch it, I have to make a call between the fial time and the reregister time.

The last step there, "Networks" is still functionally the same, but the GUI has been updated.

I like Vultr's stat page.
Here is the network usage of a PBX with ~80 extensions (all pjsip, if that matters) and 15 simultaneous calls at peak.

Here is the network graph from FreePBX itself.

More things for the home lab. That's a lot of writing, thank you!