ML
    • Recent
    • Categories
    • Tags
    • Popular
    • Users
    • Groups
    • Register
    • Login

    Wiping Data or Shredding the Drive

    Scheduled Pinned Locked Moved IT Discussion
    35 Posts 10 Posters 4.5k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • gjacobseG
      gjacobse @DustinB3403
      last edited by

      @DustinB3403 said:

      @gjacobse I hope that the company made them buy that wrench and pay for the damage to the teeth.

      lol,.. I think it only chipped like one tooth, and it wasn't enough to slow that beast down.

      My best on it was shredding, and bailing about 1700 pounds of paper. Most times we ran three people on it. Two on the infeeder, one on the fork truck / bailer to tie it up.

      I should have died in that job three times. Just about rolled the lift, had a 1600lbs bale of paper fall on the lift, and about lost a finger... Boiled over the lift loading a 53' trailer... had to get it out the bay as there was another 53' trailer to load too...

      1 Reply Last reply Reply Quote 0
      • DashrenderD
        Dashrender
        last edited by

        The local place around here charges $5 to shred a drive. I shred when they are EOL, or small enough that I don't care about them.

        I DBAN if I'm going to reuse.

        1 Reply Last reply Reply Quote 0
        • DashrenderD
          Dashrender
          last edited by

          But I've also used them for target practice. I'm personally not worried about the government trying to recover the data on the drives. And I'm not worried about normal criminals trying to recover data because the cost involved would most likely be higher than the value of the data gained.

          Drilling/shooting, totally fine in my opinion.

          brianlittlejohnB 1 Reply Last reply Reply Quote 1
          • brianlittlejohnB
            brianlittlejohn @Dashrender
            last edited by

            @Dashrender said:

            But I've also used them for target practice. I'm personally not worried about the government trying to recover the data on the drives. And I'm not worried about normal criminals trying to recover data because the cost involved would most likely be higher than the value of the data gained.

            Drilling/shooting, totally fine in my opinion.

            Shooting gives you a little stress relief too!

            MattSpellerM 1 Reply Last reply Reply Quote 1
            • MattSpellerM
              MattSpeller @brianlittlejohn
              last edited by

              @brianlittlejohn Can confirm. Recommend only rifle calibers for solid penetration. Shotgun slugs are also HIGHLY recommended. Compete for distance & best flip with your buddies.

              stacksofplatesS 1 Reply Last reply Reply Quote 0
              • brianlittlejohnB
                brianlittlejohn
                last edited by

                Rifle round for complete destruction. I had a WD stop .40 handgun round.

                1 Reply Last reply Reply Quote 0
                • DustinB3403D
                  DustinB3403
                  last edited by

                  I can't say that I've ever been so upset at something that I've need to shoot it.

                  But that's just me.

                  dafyreD 1 Reply Last reply Reply Quote 0
                  • dafyreD
                    dafyre @DustinB3403
                    last edited by

                    @DustinB3403 Being upset is not required to enjoy shooting. But shooting at targets is much better than shooting at people.

                    1 Reply Last reply Reply Quote 0
                    • DustinB3403D
                      DustinB3403
                      last edited by

                      ~But people can dodge, duck dive and dodge.....

                      brianlittlejohnB 1 Reply Last reply Reply Quote 1
                      • brianlittlejohnB
                        brianlittlejohn @DustinB3403
                        last edited by

                        If you can dodge a wrench...

                        1 Reply Last reply Reply Quote 3
                        • DustinB3403D
                          DustinB3403
                          last edited by

                          Someone gets it!

                          1 Reply Last reply Reply Quote 1
                          • DustinB3403D
                            DustinB3403
                            last edited by

                            If you can dodge a car!

                            1 Reply Last reply Reply Quote 0
                            • stacksofplatesS
                              stacksofplates @MattSpeller
                              last edited by stacksofplates

                              @MattSpeller said:

                              @brianlittlejohn Can confirm. Recommend only rifle calibers for solid penetration. Shotgun slugs are also HIGHLY recommended. Compete for distance & best flip with your buddies.

                              Using these:

                              Dupo2028.jpg

                              However at $3 a round, it might be a little pricy.

                              DustinB3403D 1 Reply Last reply Reply Quote 1
                              • DustinB3403D
                                DustinB3403 @stacksofplates
                                last edited by

                                @johnhooks Probably considering how few drives those might actually go through....

                                You'd be better of purchasing a bearing press, and high powered magnets.

                                stacksofplatesS 1 Reply Last reply Reply Quote 0
                                • stacksofplatesS
                                  stacksofplates @DustinB3403
                                  last edited by stacksofplates

                                  @DustinB3403 said:

                                  @johnhooks Probably considering how few drives those might actually go through....

                                  You'd be better of purchasing a bearing press, and high powered magnets.

                                  They're solid steel. They'll go through. The plastic never holds up like in the picture, the petals come off.

                                  1 Reply Last reply Reply Quote 1
                                  • 1
                                  • 2
                                  • 2 / 2
                                  • First post
                                    Last post