ZeroTier + Active Directory Authentication
-
@Dashrender said:
I'm curious though.. what happens when two NICs have IPs in the same range? This would be the case when a laptop is in the office.
Why would that happen with laptops?
-
@scottalanmiller said:
@Dashrender said:
I'm curious though.. what happens when two NICs have IPs in the same range? This would be the case when a laptop is in the office.
Why would that happen with laptops?
He means if they use the same IP range for both the LAN and the ZT network... what would happen if a laptop got 192.168.16.16 on the LAN, as well as 192.168.16.16 on the ZT network.
-
@dafyre said:
@scottalanmiller said:
@Dashrender said:
I'm curious though.. what happens when two NICs have IPs in the same range? This would be the case when a laptop is in the office.
Why would that happen with laptops?
He means if they use the same IP range for both the LAN and the ZT network... what would happen if a laptop got 192.168.16.16 on the LAN, as well as 192.168.16.16 on the ZT network.
Oh, you can't do that. The devices would freak out. It's as simple as... you can't.
But... when would this happen? Why would you choose a ZT network that overlaps with the LAN?
-
Oh, you can't do that. The devices would freak out. It's as simple as... you can't.
But... when would this happen? Why would you choose a ZT network that overlaps with the LAN?Couldn't you create two separate reservations--one for the LAN and one for ZT?
-
@scottalanmiller said:
@dafyre said:
@scottalanmiller said:
@Dashrender said:
I'm curious though.. what happens when two NICs have IPs in the same range? This would be the case when a laptop is in the office.
Why would that happen with laptops?
He means if they use the same IP range for both the LAN and the ZT network... what would happen if a laptop got 192.168.16.16 on the LAN, as well as 192.168.16.16 on the ZT network.
Oh, you can't do that. The devices would freak out. It's as simple as... you can't.
But... when would this happen? Why would you choose a ZT network that overlaps with the LAN?
I think that may have been something that someone read a little too much into what @adam-ierymenko was saying about bridging (either in this thread, or another).
-
@wirestyle22 said:
Oh, you can't do that. The devices would freak out. It's as simple as... you can't.
But... when would this happen? Why would you choose a ZT network that overlaps with the LAN?Couldn't you create two separate reservations--one for the LAN and one for ZT?
Right, but then how does the computer know which IP range to actually talk from?
-
@wirestyle22 said:
Oh, you can't do that. The devices would freak out. It's as simple as... you can't.
But... when would this happen? Why would you choose a ZT network that overlaps with the LAN?Couldn't you create two separate reservations--one for the LAN and one for ZT?
DHCP would not work, you'd have a mess.
-
@scottalanmiller said:
@wirestyle22 said:
Oh, you can't do that. The devices would freak out. It's as simple as... you can't.
But... when would this happen? Why would you choose a ZT network that overlaps with the LAN?Couldn't you create two separate reservations--one for the LAN and one for ZT?
DHCP would not work, you'd have a mess.
I was thinking statically assigned IP's
-
@dafyre said:
@scottalanmiller said:
@Dashrender said:
I'm curious though.. what happens when two NICs have IPs in the same range? This would be the case when a laptop is in the office.
Why would that happen with laptops?
He means if they use the same IP range for both the LAN and the ZT network... what would happen if a laptop got 192.168.16.16 on the LAN, as well as 192.168.16.16 on the ZT network.
uh.. no - that shouldn't happen.
So looking at the ZT docs on creating a bridge: The LAN will use 192.168.0.x and ZT will use 192.168.1.x. DHCP on the LAN will only provide 192.168.0.x addresses so you'll never have a conflict of IPs (wasn't part of my concern)
But since this is all in the same /22 you now have two adapters on the same network. -
@wirestyle22 said:
@scottalanmiller said:
@wirestyle22 said:
Oh, you can't do that. The devices would freak out. It's as simple as... you can't.
But... when would this happen? Why would you choose a ZT network that overlaps with the LAN?Couldn't you create two separate reservations--one for the LAN and one for ZT?
DHCP would not work, you'd have a mess.
I was thinking statically assigned IP's
Bottom line, you cannot overlap the same network. It conceptually doesn't even make sense. The machine would have no idea how to differentiate between the two because they are literally the same network.
Static, dynamic, reservations.. doesn't matter. You can't layer the same network on itself.
-
@Dashrender said:
@dafyre said:
@scottalanmiller said:
@Dashrender said:
I'm curious though.. what happens when two NICs have IPs in the same range? This would be the case when a laptop is in the office.
Why would that happen with laptops?
He means if they use the same IP range for both the LAN and the ZT network... what would happen if a laptop got 192.168.16.16 on the LAN, as well as 192.168.16.16 on the ZT network.
uh.. no - that shouldn't happen.
So looking at the ZT docs on creating a bridge: The LAN will use 192.168.0.x and ZT will use 192.168.1.x. DHCP on the LAN will only provide 192.168.0.x addresses so you'll never have a conflict of IPs (wasn't part of my concern)
But since this is all in the same /22 you now have two adapters on the same network.I don't have the docs in from of me, but why is it making two addresses on the same LAN?
-
@scottalanmiller said:
@Dashrender said:
@dafyre said:
@scottalanmiller said:
@Dashrender said:
I'm curious though.. what happens when two NICs have IPs in the same range? This would be the case when a laptop is in the office.
Why would that happen with laptops?
He means if they use the same IP range for both the LAN and the ZT network... what would happen if a laptop got 192.168.16.16 on the LAN, as well as 192.168.16.16 on the ZT network.
uh.. no - that shouldn't happen.
So looking at the ZT docs on creating a bridge: The LAN will use 192.168.0.x and ZT will use 192.168.1.x. DHCP on the LAN will only provide 192.168.0.x addresses so you'll never have a conflict of IPs (wasn't part of my concern)
But since this is all in the same /22 you now have two adapters on the same network.I don't have the docs in from of me, but why is it making two addresses on the same LAN?
because that's how bridging works. Bridging assumes NO routes.. everything is on the same subnet.
-
https://www.zerotier.com/community/topic/5/bridging-ethernet-to-zerotier-virtual-networks-on-linux
Configure the DHCP Server in the Office LAN to give leases in the range 10.0.0.100-10.0.0.200.
Configure the ZeroTier portal to manage IP addresses in the range range 10.0.1.100-10.0.1.200. Note how the address ranges are in the same 10.0.0.0/16 subnet, but have a unique pool of IP addresses.The instructions have you create a giant subnet /16 the LAN will be on x.x.0.x and the ZT will be on x.x.1.x No routers involved for communication here.
-
So if I'm reading this correctly, using bridging means that no ZT devices can ever be on the local network, except the one server providing the bridging, which it's doing through a disconnected NIC port that's acting like a switch port.
The typical ZT clients would need to never be on that same physical network.
-
@Dashrender said:
So if I'm reading this correctly, using bridging means that no ZT devices can ever be on the local network, except the one server providing the bridging, which it's doing through a disconnected NIC port that's acting like a switch port.
The typical ZT clients would need to never be on that same physical network.
There is no reason they cannot be on the same network.
I can have my laptop plugged in to the LAN and WiFi at the same time. they get two different addresses. This is no different with ZT. it is a separate adapter.Basic IP functions here, nothing complicated.
-
@Dashrender said:
https://www.zerotier.com/community/topic/5/bridging-ethernet-to-zerotier-virtual-networks-on-linux
Configure the DHCP Server in the Office LAN to give leases in the range 10.0.0.100-10.0.0.200.
Configure the ZeroTier portal to manage IP addresses in the range range 10.0.1.100-10.0.1.200. Note how the address ranges are in the same 10.0.0.0/16 subnet, but have a unique pool of IP addresses.The instructions have you create a giant subnet /16 the LAN will be on x.x.0.x and the ZT will be on x.x.1.x No routers involved for communication here.
I totally missed that bit before... I think I am going to try it out again.
-
@JaredBusch said:
@Dashrender said:
So if I'm reading this correctly, using bridging means that no ZT devices can ever be on the local network, except the one server providing the bridging, which it's doing through a disconnected NIC port that's acting like a switch port.
The typical ZT clients would need to never be on that same physical network.
There is no reason they cannot be on the same network.
I can have my laptop plugged in to the LAN and WiFi at the same time. they get two different addresses. This is no different with ZT. it is a separate adapter.Basic IP functions here, nothing complicated.
Good point - I've done that before too. Though It's my understanding that the default in Windows - when the LAN is connected, the WLAN is ignored.
-
@dafyre said:
@Dashrender said:
https://www.zerotier.com/community/topic/5/bridging-ethernet-to-zerotier-virtual-networks-on-linux
Configure the DHCP Server in the Office LAN to give leases in the range 10.0.0.100-10.0.0.200.
Configure the ZeroTier portal to manage IP addresses in the range range 10.0.1.100-10.0.1.200. Note how the address ranges are in the same 10.0.0.0/16 subnet, but have a unique pool of IP addresses.The instructions have you create a giant subnet /16 the LAN will be on x.x.0.x and the ZT will be on x.x.1.x No routers involved for communication here.
I totally missed that bit before... I think I am going to try it out again.
Well that might be why your Bridge didn't work
I don't really want a bridge - I want a ZT to LAN router. Then you could have all of your printers on your production network, all of your users on open/free network, and the ZT would still provide IP access to the printers and their real IPs.
The problem with this is putting a route into the local machine that ensures that traffic bound for that routed network goes through ZT, not the default gateway of the end point.
-
@Dashrender said:
@JaredBusch said:
@Dashrender said:
So if I'm reading this correctly, using bridging means that no ZT devices can ever be on the local network, except the one server providing the bridging, which it's doing through a disconnected NIC port that's acting like a switch port.
The typical ZT clients would need to never be on that same physical network.
There is no reason they cannot be on the same network.
I can have my laptop plugged in to the LAN and WiFi at the same time. they get two different addresses. This is no different with ZT. it is a separate adapter.Basic IP functions here, nothing complicated.
Good point - I've done that before too. Though It's my understanding that the default in Windows - when the LAN is connected, the WLAN is ignored.
Not even close to true. Windows does not care about it. You need to set that up in BIOS or have HP/Dell software running to do it automagically.
In Windows, you can set adapter order. But some things like Pertino reinstall the adapter when they update and that puts it back on the top of the list.
This is where you specify it in Windows.
-
@Dashrender said:
@dafyre said:
@Dashrender said:
https://www.zerotier.com/community/topic/5/bridging-ethernet-to-zerotier-virtual-networks-on-linux
Configure the DHCP Server in the Office LAN to give leases in the range 10.0.0.100-10.0.0.200.
Configure the ZeroTier portal to manage IP addresses in the range range 10.0.1.100-10.0.1.200. Note how the address ranges are in the same 10.0.0.0/16 subnet, but have a unique pool of IP addresses.The instructions have you create a giant subnet /16 the LAN will be on x.x.0.x and the ZT will be on x.x.1.x No routers involved for communication here.
I totally missed that bit before... I think I am going to try it out again.
Well that might be why your Bridge didn't work
I don't really want a bridge - I want a ZT to LAN router. Then you could have all of your printers on your production network, all of your users on open/free network, and the ZT would still provide IP access to the printers and their real IPs.
The problem with this is putting a route into the local machine that ensures that traffic bound for that routed network goes through ZT, not the default gateway of the end point.
I've built one of those... I'll do it again and document it this weekend.