CAT6 End to End?
-
@wirestyle22 said:
@aaronstuder said:
Do you run CAT 6 End to End? or Do you use 5e sometimes?
The exception would be if you're doing a lot of video streaming, etc.
internally. If you're streaming from the internet, unless you're streaming at greater than 1 Gb, it would still be pointless
-
@scottalanmiller said:
@aaronstuder said:
Do you run CAT 6 End to End? or Do you use 5e sometimes?
Pretty much just CAT5e. Cheaper, easier to run.
how is it easier to run? It all depends on if you get solid to stranded wire.
-
@david.wiese said:
@scottalanmiller said:
@aaronstuder said:
Do you run CAT 6 End to End? or Do you use 5e sometimes?
Pretty much just CAT5e. Cheaper, easier to run.
how is it easier to run? It all depends on if you get solid to stranded wire.
termination
-
@david.wiese said:
@scottalanmiller said:
@aaronstuder said:
Do you run CAT 6 End to End? or Do you use 5e sometimes?
Pretty much just CAT5e. Cheaper, easier to run.
how is it easier to run? It all depends on if you get solid to stranded wire.
Even all stranded, CAT6 is quite a bit more effort.
-
@scottalanmiller said:
@david.wiese said:
@scottalanmiller said:
@aaronstuder said:
Do you run CAT 6 End to End? or Do you use 5e sometimes?
Pretty much just CAT5e. Cheaper, easier to run.
how is it easier to run? It all depends on if you get solid to stranded wire.
Even all stranded, CAT6 is quite a bit more effort.
I've pulled 5e and 6 in through the rafters in my shop and to me there is no discernable difference between the 2. Even when punching down/terminating the cables.
-
Yeah I've only seen CAT6 run (had it run) because my installer had a bunch of it and was selling it for less than retail.
Had 15 drops put in for the same cost as CAT5e
-
@david.wiese said:
I've pulled 5e and 6 in through the rafters in my shop and to me there is no discernable difference between the 2. Even when punching down/terminating the cables.
Can't explain how you see them as the same, the termination components that I've seen are quite different, so much so that one is very easy and one is rather difficult.
-
@david.wiese said:
@scottalanmiller said:
@david.wiese said:
@scottalanmiller said:
@aaronstuder said:
Do you run CAT 6 End to End? or Do you use 5e sometimes?
Pretty much just CAT5e. Cheaper, easier to run.
how is it easier to run? It all depends on if you get solid to stranded wire.
Even all stranded, CAT6 is quite a bit more effort.
I've pulled 5e and 6 in through the rafters in my shop and to me there is no discernable difference between the 2. Even when punching down/terminating the cables.
Did you use CAT certified panels and RJ45's?
-
Company now uses all Cat6 - but I miss Cat 5e, was easier to run and terminate, easier to bend etc too...
-
@Dashrender said:
@david.wiese said:
@scottalanmiller said:
@david.wiese said:
@scottalanmiller said:
@aaronstuder said:
Do you run CAT 6 End to End? or Do you use 5e sometimes?
Pretty much just CAT5e. Cheaper, easier to run.
how is it easier to run? It all depends on if you get solid to stranded wire.
Even all stranded, CAT6 is quite a bit more effort.
I've pulled 5e and 6 in through the rafters in my shop and to me there is no discernable difference between the 2. Even when punching down/terminating the cables.
Did you use CAT certified panels and RJ45's?
we use keystones and punchdown blocks. I typically don't terminate with rj45s
-
@scottalanmiller said:
@david.wiese said:
I've pulled 5e and 6 in through the rafters in my shop and to me there is no discernable difference between the 2. Even when punching down/terminating the cables.
Can't explain how you see them as the same, the termination components that I've seen are quite different, so much so that one is very easy and one is rather difficult.
The termination is a bit different, not much though. After a little practice I can terminate a cat6 just as fast as cat5e with RJ45 plugs. As far as punchdown and keystone jacks they are the same.
-
@Dashrender said:
@wirestyle22 said:
@aaronstuder said:
Do you run CAT 6 End to End? or Do you use 5e sometimes?
The exception would be if you're doing a lot of video streaming, etc.
internally. If you're streaming from the internet, unless you're streaming at greater than 1 Gb, it would still be pointless
Correct sir!
-
@brianlittlejohn said:
@scottalanmiller said:
@david.wiese said:
I've pulled 5e and 6 in through the rafters in my shop and to me there is no discernable difference between the 2. Even when punching down/terminating the cables.
Can't explain how you see them as the same, the termination components that I've seen are quite different, so much so that one is very easy and one is rather difficult.
The termination is a bit different, not much though. After a little practice I can terminate a cat6 just as fast as cat5e with RJ45 plugs. As far as punchdown and keystone jacks they are the same.
Still slower for me, due to the fiddly plastic core that needs cutting out...
-
@NattNatt said:
Company now uses all Cat6 - but I miss Cat 5e, was easier to run and terminate, easier to bend etc too...
You won't miss 5e in a couple years when 10gig switching is dirt cheap
-
@MattSpeller said:
@NattNatt said:
Company now uses all Cat6 - but I miss Cat 5e, was easier to run and terminate, easier to bend etc too...
You won't miss 5e in a couple years when 10gig switching is dirt cheap
I'm pretty sure this is what they promised a few years before Mad Max became actual human history but what do I know. My network is held together by bubblegum and soothing words
-
@MattSpeller said:
@NattNatt said:
Company now uses all Cat6 - but I miss Cat 5e, was easier to run and terminate, easier to bend etc too...
You won't miss 5e in a couple years when 10gig switching is dirt cheap
That will be a few years yet, and I don't see adoption being that rapid. Few people have a means of using that even today.
-
@wirestyle22 said:
@MattSpeller said:
@NattNatt said:
Company now uses all Cat6 - but I miss Cat 5e, was easier to run and terminate, easier to bend etc too...
You won't miss 5e in a couple years when 10gig switching is dirt cheap
I'm pretty sure this is what they promised a few years before Mad Max became actual human history but what do I k now. My network is held together by bubblegum and soothing words
Blood, sweat and bailing wire here - can relate.
-
@MattSpeller said:
@wirestyle22 said:
@MattSpeller said:
@NattNatt said:
Company now uses all Cat6 - but I miss Cat 5e, was easier to run and terminate, easier to bend etc too...
You won't miss 5e in a couple years when 10gig switching is dirt cheap
I'm pretty sure this is what they promised a few years before Mad Max became actual human history but what do I k now. My network is held together by bubblegum and soothing words
Blood, sweat and bailing wire here - can relate.
Me as a sysadmin
-
@scottalanmiller said:
@MattSpeller said:
@NattNatt said:
Company now uses all Cat6 - but I miss Cat 5e, was easier to run and terminate, easier to bend etc too...
You won't miss 5e in a couple years when 10gig switching is dirt cheap
That will be a few years yet, and I don't see adoption being that rapid. Few people have a means of using that even today.
With the prevalence of cloud computing it may just never see the demand that gig got. I think that'll be the primary hiccup in it's adoption. That and quality WIFI anyway.
-
@MattSpeller said:
@scottalanmiller said:
@MattSpeller said:
@NattNatt said:
Company now uses all Cat6 - but I miss Cat 5e, was easier to run and terminate, easier to bend etc too...
You won't miss 5e in a couple years when 10gig switching is dirt cheap
That will be a few years yet, and I don't see adoption being that rapid. Few people have a means of using that even today.
With the prevalence of cloud computing it may just never see the demand that gig got. I think that'll be the primary hiccup in it's adoption. That and quality WIFI anyway.
In the datacenter I definitely see 10 GbE taking over... but at the end point - no way except for rare specialty conditions - like the video processing station.
