Cloning XenServer on USB or SD
-
@DustinB3403 said
So yes, a clean install is recommended.
Hear ya loud and clear.
Hopefully XS will allow me to transfer both directions for migrations, then none of this will be an issue.
Or, I'll maybe just buy a refurb server from xByte for this purpose.
-
This is the command I usually use to clone one drive to another identical drive.
dd if=/dev/sdX of=/dev/sdY bs=512 conv=noerror,sync
It uses the default block size to make a direct copy and keeps any errors from interrupting the process.
I've had problems come from changing to a larger blocksize before, so I usually just stick with the default of 512. If you are going to be moving between disks/partitions of different sizes you'll just need to start with a smaller image and make sure you resize your partitions and fix the filesystems after cloning. If you have a standard image you are working from you can test this out and find the largest block size that is stable and works for your specific task.
I wrote a small program in BASH that did a quick disk test/verification and automated the process of writing a standard image onto sd-cards of varying sizes (2GB up to 32GB) using dd and fdisk. It ended up replacing some old piece of software that ran on Windows and could not properly detect the newer larger capacity sd cards that our client wanted to start using.
-
Strangely enough ImageUSB did it properly.
But I'm not sure it's worth the risk of trying what I want to do.
I'll get everything upgraded to XS7 and then start clean installing.
-
@scottalanmiller said
Assuming the devices refer to the two USB devices:
dd if=dev/sda1 of=/dev/sdb1
If you are doing the entire disk (such as with XS which creates multiple partitions) why wouldn't it be...
dd if=/dev/sda of=/dev/sdb
-
@BRRABill said in Cloning XenServer on USB or SD:
@scottalanmiller said
Assuming the devices refer to the two USB devices:
dd if=dev/sda1 of=/dev/sdb1
If you are doing the entire disk (such as with XS which creates multiple partitions) why wouldn't it be...
dd if=/dev/sda of=/dev/sdb
You have to copy what there is to where you want it. If the filesystem is on /dev/sda1 you don't want /dev/sda or you are copying the partitioning layer with it.
-
@scottalanmiller said
You have to copy what there is to where you want it. If the filesystem is on /dev/sda1 you don't want /dev/sda or you are copying the partitioning layer with it.
But if I want to make an exact clone of the USB for DR purposes, I'd want the partitioning layer, no?
-
@BRRABill said in Cloning XenServer on USB or SD:
@scottalanmiller said
You have to copy what there is to where you want it. If the filesystem is on /dev/sda1 you don't want /dev/sda or you are copying the partitioning layer with it.
But if I want to make an exact clone of the USB for DR purposes, I'd want the partitioning layer, no?
Never tried that. Normally we partition manually. Maybe someone has tried this to know about reliability.
-
@scottalanmiller said in Cloning XenServer on USB or SD:
@DustinB3403 said in Cloning XenServer on USB or SD:
@scottalanmiller said in Cloning XenServer on USB or SD:
The standard tool for cloning is the dd command. No third party tools needed.
Can you provide a sample step by step, as I've not used DD on linux before and the documentation I've seen has been "sloppy" IMO.
Assuming the devices refer to the two USB devices:
dd if=dev/sda1 of=/dev/sdb1
So the poster asked for an example to clone the USB boot device, and this is what was given.
Are you saying you'd dd each of the partitions individually?
I am now confused.
-
I assume that there is only one partition. You can check yours but there should not be multiple partitions.
-
@scottalanmiller said in Cloning XenServer on USB or SD:
I assume that there is only one partition. You can check yours but there should not be multiple partitions.
This is how XS7 sets it up, at least...
sdb 8:16 0 74.5G 0 disk ├─sdb1 8:17 0 18G 0 part / ├─sdb2 8:18 0 18G 0 part ├─sdb3 8:19 0 512M 0 part ├─sdb5 8:21 0 4G 0 part /var/log └─sdb6 8:22 0 1G 0 part [SWAP]