Slow PC
-
If you want to image it, because it's a RAID1, use Clonezilla to grab an image of the RAID, break the RAID, restore the image to a single disk, and format the other disk to use as a data drive. That should work..
-
@thanksaj said:
When you replaced the drive, could it be one is SATA II and the other is SATA III? Is one 5400RPM and the other 7200RPM?
I can't quite remember the details, but I think the drives aren't identical models, as the original model is no longer available, but I think they are the same spec. I tried to get one with the same spec anyway. I'm pretty definate they're the same speed anyway, but it's possible the new one is SATA III and the old one is SATA II.
-
@Carnival-Boy said:
@thanksaj said:
When you replaced the drive, could it be one is SATA II and the other is SATA III? Is one 5400RPM and the other 7200RPM?
I can't quite remember the details, but I think the drives aren't identical models, as the original model is no longer available, but I think they are the same spec. I tried to get one with the same spec anyway. I'm pretty definate they're the same speed anyway, but it's possible the new one is SATA III and the old one is SATA II.
That could be a bottleneck. You're only as fast as your slowest link.
-
Different drives will be a bottleneck, but typically a tiny one, possibly too small to measure. Definitely would not cause the end user to mention it unless they were drastically different.
-
Ghosting a degraded array is fine. It's not failed, it is just degraded. If it actually failed you couldn't boot or anything.
-
I've found a spare disk, so I can clone the array without removing any of the drives.
Having cloned it, do I need to remove the old array in the RAID software, or can I just remove the two old disk and replace them with the new, single, cloned disk. Will the RAID software go "ah, he's replaced the drives, I'll make a note that he's no longer using RAID and boot from this new disk" or will it go "ah, two drives are missing, I'm not going to boot".
-
@Carnival-Boy said:
I've found a spare disk, so I can clone the array without removing any of the drives.
Having cloned it, do I need to remove the old array in the RAID software, or can I just remove the two old disk and replace them with the new, single, cloned disk. Will the RAID software go "ah, he's replaced the drives, I'll make a note that he's no longer using RAID and boot from this new disk" or will it go "ah, two drives are missing, I'm not going to boot".
You'll need to change your boot settings from RAID to probably AHCI I think it is.
-
@thanksaj said:
@Carnival-Boy said:
I've found a spare disk, so I can clone the array without removing any of the drives.
Having cloned it, do I need to remove the old array in the RAID software, or can I just remove the two old disk and replace them with the new, single, cloned disk. Will the RAID software go "ah, he's replaced the drives, I'll make a note that he's no longer using RAID and boot from this new disk" or will it go "ah, two drives are missing, I'm not going to boot".
You'll need to change your boot settings from RAID to probably AHCI I think it is.
Also, double-check your boot priority/order to make sure it recognizes the single disk.
-
You'll need to turn off the RAID setting or it will keep looking for one.
-
@scottalanmiller said:
You'll need to turn off the RAID setting or it will keep looking for one.
Yup, exactly...
-
@Carnival-Boy said:
Will the RAID software go "ah, he's replaced the drives, I'll make a note that he's no longer using RAID and boot from this new disk"
It did this. I'm not sure what you mean by turning off the RAID setting or changing boot settings. There doesn't seem to be anything to change. The RAID software now just says a RAID array is not present and it boots normally. Storage options in the BIOS is set to SATA Emultation = RAID+AHCI.
Performance seems better, but I'll wait and see what the user thinks. I noticed the paging file was disabled for some reason, so I've enabled it - not sure if that will make any difference.
-
@Carnival-Boy said:
@Carnival-Boy said:
Will the RAID software go "ah, he's replaced the drives, I'll make a note that he's no longer using RAID and boot from this new disk"
It did this. I'm not sure what you mean by turning off the RAID setting or changing boot settings. There doesn't seem to be anything to change. The RAID software now just says a RAID array is not present and it boots normally. Storage options in the BIOS is set to SATA Emultation = RAID+AHCI.
Performance seems better, but I'll wait and see what the user thinks. I noticed the paging file was disabled for some reason, so I've enabled it - not sure if that will make any difference.
Even if you have plenty of RAM, I've made the mistake of disabling the page file before, and it seriously hurts system performance, even when you have more than enough RAM to where you shouldn't need it.
-
I'm not sure who would have disabled it. It wasn't me. 16GB RAM isn't actually very much for the type of software that runs on this workstation (graphics based).
-
@Carnival-Boy said:
I'm not sure who would have disabled it. It wasn't me. 16GB RAM isn't actually very much for the type of software that runs on this workstation (graphics based).
As long as you have a halfway decent graphics card, it's plenty. CAD is more graphic intensive than resource intensive. It just becomes RAM intensive when you run out of video RAM to use.
-
I never know how to spec workstations. Is this an area of expertise for you? How do you know when the graphics card has run out of RAM? I know 16GB is listed by Autodesk as as the minimum required RAM for complex assemblies. We currently use Nvidia K2000 cards and they only have 2GB RAM, but it starts getting very expensive to buy anything better.
Of course, my users all say their workstations are great when I first get them, but after a year or so they are bitching and whining about needing something more powerful. Generally I find that users adjust their workflow according to the spec of their machine, so the more power you give them, the more they will consume. After all, I believe Toy Story was created on a workstation less powerful than the ones we use and Toy Story is way better than anything my users have ever produced!
I'm wondering if cloud rendering is the way to go though?
-
@Carnival-Boy said:
Performance seems better, but I'll wait and see what the user thinks. I noticed the paging file was disabled for some reason, so I've enabled it - not sure if that will make any difference.
Should. Windows likes having a paging file. So does Linux, actually. Doesn't have to be huge. 2GB is probably plenty. Depends on your workload, but if you could run with none, then having a small one is fine. I'd probably opt for letting Windows determine the size and if setting manually don't drop below 4GB.
-
@Carnival-Boy said:
I'm not sure who would have disabled it. It wasn't me. 16GB RAM isn't actually very much for the type of software that runs on this workstation (graphics based).
If you are pushing the memory limits in any way (using the majority of it), then having the page file turned on should really help. Windows will page out what it thinks is unneeded and use the real memory for performance enhancing things like buffers and cache. It's an intelligent algorithm designed to maximize performance given the available resources. Tends to work pretty well. Same as UNIX does.
-
@Carnival-Boy said:
I never know how to spec workstations. Is this an area of expertise for you? How do you know when the graphics card has run out of RAM? I know 16GB is listed by Autodesk as as the minimum required RAM for complex assemblies. We currently use Nvidia K2000 cards and they only have 2GB RAM, but it starts getting very expensive to buy anything better.
You are correct. 16GB is a "lot" but for real CAD workstations, it's nothing crazy at all. 24-32GB is realistic. There is a ton of potential modeling data that isn't graphical data that has to go into memory.
K2000 are nice but rather on the lower end for commercial CAD applications. If you are running out of 2GB of video memory you will likely really, really know it. It can't just use system memory and "go slower", if the graphics rendering doesn't fit into the memory, then it doesn't fit and that's it. It's extremely unlikely that you are out of GPU memory, unless you are doing some crazy CUDA offload work separate from your graphics (not likely, but possible.) It's only system memory that you have to worry about. The application assumes that 2GB is basically the standard that it is going to get, you can get more, but 2GB is still extremely common.
-
@Carnival-Boy said:
After all, I believe Toy Story was created on a workstation less powerful than the ones we use and Toy Story is way better than anything my users have ever produced!
Toy Story was "created" on a workstation long ago. But it was rendered on a massive computational cluster. I have friends who run those systems for movies on par with that and those are hundreds of millions of dollars in high end HPCs that each node has way more power than your workstations.
The difference is that you both create and render on a single device. So the workstation power that you need is higher, but only a little because you are rendering only one thing and only for one person. Toy Story had to render at crazy quality, millions of scenes, many times.
-
@Carnival-Boy said:
I'm wondering if cloud rendering is the way to go though?
Not likely for CAD. Requires a lot of bandwidth and CAD doesn't actually render all that much. The cost would likely pay for you to get higher end GPUs very quickly and higher end GPUs should get you a lot more mileage. Going to cloud rendering means a LONG wait for everything. Like hours. It's useful for post production shops that work all day then submit their rendering job online to run for a few days. Over the period of days, the speed of the online system makes up for the long upload, download and queue times.
