Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s
-
Have you tried disabling VMQ on the NIC Adapters in the VM? Some say this helps, others say it doesn't. I generally have good results with it.
-
I'll probably wait till everyone leaves and come in the morning early to double-check the BIOS. The disabling of the VMQ however, when I ran the command it didn't return that I had anything enabled....
I checked the Xen nic, and it doesn't have a listing in the advanced tab for the VMQ
-
@krisleslie said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
I'll probably wait till everyone leaves and come in the morning early to double-check the BIOS. The disabling of the VMQ however, when I ran the command it didn't return that I had anything enabled....
I checked the Xen nic, and it doesn't have a listing in the advanced tab for the VMQ
I figured it wouldn't, but I was putting it out there anyway.
If you look at the NIC status, what does it show the connected speed?
-
@krisleslie no one has mentioned it, but are you sure that you have GigE end to end? 10MB/s is the speed cap when you have a 100Mb/s network link somewhere.
-
You could also have a bad switch in the mix.... that was the case for someone around here recently.
-
@dafyre said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
ook at the NIC status, what does it show the connected speed?
1 Gb
-
@scottalanmiller can't be it, because sometimes I see it do 60 Mbps + like during OS install or if I happen to catch it.
-
Potential bad switch as in maybe one of the interfaces is bad? I think a long time ago me and scott thought about switching to 10 gb interconnects for each switch
-
Can't be the NIC (???) I'm doing like a file transfer from one folder to another on the same disk/vm of the vm that I'm running. When I tried last night to copy vm to vm yea after 10 hours only 1/3rd got done give or take an hour or so.
-
@krisleslie said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
Can't be the NIC (???) I'm doing like a file transfer from one folder to another on the same disk/vm of the vm that I'm running. When I tried last night to copy vm to vm yea after 10 hours only 1/3rd got done give or take an hour or so.
OK that takes the switch out of the situation.
-
@krisleslie said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
@dafyre said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
ook at the NIC status, what does it show the connected speed?
1 Gb
In the VM or at the Host?
-
As I'm running Crystal Disk Mark the speeds are so horrible I want to vomit.
-
@dafyre Both ( default server card)
-
@krisleslie said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
card
CrystalDiskMark 6.0.1 x64 (C) 2007-2018 hiyohiyo
Crystal Dew World : https://crystalmark.info/-
MB/s = 1,000,000 bytes/s [SATA/600 = 600,000,000 bytes/s]
-
KB = 1000 bytes, KiB = 1024 bytes
Sequential Read (Q= 32,T= 1) : 69.078 MB/s
Sequential Write (Q= 32,T= 1) : 101.986 MB/s
Random Read 4KiB (Q= 8,T=
: 9.545 MB/s [ 2330.3 IOPS]
Random Write 4KiB (Q= 8,T= : 13.363 MB/s [ 3262.5 IOPS]
Random Read 4KiB (Q= 32,T= 1) : 9.795 MB/s [ 2391.4 IOPS]
Random Write 4KiB (Q= 32,T= 1) : 13.832 MB/s [ 3377.0 IOPS]
Random Read 4KiB (Q= 1,T= 1) : 0.751 MB/s [ 183.3 IOPS]
Random Write 4KiB (Q= 1,T= 1) : 3.714 MB/s [ 906.7 IOPS]Test : 1024 MiB [C: 97.6% (1463.7/1499.7 GiB)] (x5) [Interval=5 sec]
Date : 2020/02/05 17:56:34
OS : Windows Server 2012 R2 Server Standard (full installation) [6.3 Build 9600] (x64)
-
-
On that note, I'm going to the nearest bottle.
-
@krisleslie said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
@scottalanmiller can't be it, because sometimes I see it do 60 Mbps + like during OS install or if I happen to catch it.
60Mb/s is a fraction of 10MB/s, though.
-
@krisleslie said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
As I'm running Crystal Disk Mark the speeds are so horrible I want to vomit.
Drives having SMART issues, maybe?
-
Time to take a peak.
-
@krisleslie said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
Time to take a peak.
You haven't yet?
-
Nothing has raised a flag to that being an issue. Speeds like that have been present for literally every server I've used over the years with virtualization. I have a fresh new server sitting behind me that when I finish installing XCP to it tonight I bet barely yields much of anything better ;(
