XenServer installation SR issue
-
The RAID array should appear as a single drive and nothing that XS does should make a rebuild of the array needed. If that is happening, there is a deeper problem.
-
@fuznutz04 said in XenServer installation SR issue:
@DustinB3403 said in XenServer installation SR issue:
Hrm..
I wonder if there is a compatibility issue with your hardware then...
Meaning the actual physical disks, or the RAID controller? I checked, and the RAID controller is on the HCL for XS 7. The disks are a mix of drives that I had around my house. WD Reds and a WD green or two.
The drives shouldn't matter (I'd be really really surprised if it did).
I just checked you hardware as well and it is supported. I actually just installed XS7 on a desktop yesterday for a tiny project.
So I'm guessing it's a hardware problem of some sort.
Have you given XS6.5 a go on this system and see what happens?
-
@scottalanmiller said in XenServer installation SR issue:
The RAID array should appear as a single drive and nothing that XS does should make a rebuild of the array needed. If that is happening, there is a deeper problem.
It does. It shows as a single 6 TB "drive"
-
@DustinB3403 said in XenServer installation SR issue:
@fuznutz04 said in XenServer installation SR issue:
@DustinB3403 said in XenServer installation SR issue:
Hrm..
I wonder if there is a compatibility issue with your hardware then...
Meaning the actual physical disks, or the RAID controller? I checked, and the RAID controller is on the HCL for XS 7. The disks are a mix of drives that I had around my house. WD Reds and a WD green or two.
The drives shouldn't matter (I'd be really really surprised if it did).
I just checked you hardware as well and it is supported. I actually just installed XS7 on a desktop yesterday for a tiny project.
So I'm guessing it's a hardware problem of some sort.
Have you given XS6.5 a go on this system and see what happens?
No, I haven't tried 6.5 yet, only 7.
-
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
The RAID array should appear as a single drive and nothing that XS does should make a rebuild of the array needed. If that is happening, there is a deeper problem.
It does. It shows as a single 6 TB "drive"
Should not need to rebuild, then. If the underlying array is corrupting, then the issue is at the controller or disk level.
-
@fuznutz04 said in XenServer installation SR issue:
@DustinB3403 said in XenServer installation SR issue:
@fuznutz04 said in XenServer installation SR issue:
@DustinB3403 said in XenServer installation SR issue:
Hrm..
I wonder if there is a compatibility issue with your hardware then...
Meaning the actual physical disks, or the RAID controller? I checked, and the RAID controller is on the HCL for XS 7. The disks are a mix of drives that I had around my house. WD Reds and a WD green or two.
The drives shouldn't matter (I'd be really really surprised if it did).
I just checked you hardware as well and it is supported. I actually just installed XS7 on a desktop yesterday for a tiny project.
So I'm guessing it's a hardware problem of some sort.
Have you given XS6.5 a go on this system and see what happens?
No, I haven't tried 6.5 yet, only 7.
Give 6.5 a try and let us know if you have the same issue.
-
@scottalanmiller said in XenServer installation SR issue:
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
The RAID array should appear as a single drive and nothing that XS does should make a rebuild of the array needed. If that is happening, there is a deeper problem.
It does. It shows as a single 6 TB "drive"
Should not need to rebuild, then. If the underlying array is corrupting, then the issue is at the controller or disk level.
Any recommendations on what to check next on the controller and disks?
-
@DustinB3403 said in XenServer installation SR issue:
@fuznutz04 said in XenServer installation SR issue:
@DustinB3403 said in XenServer installation SR issue:
@fuznutz04 said in XenServer installation SR issue:
@DustinB3403 said in XenServer installation SR issue:
Hrm..
I wonder if there is a compatibility issue with your hardware then...
Meaning the actual physical disks, or the RAID controller? I checked, and the RAID controller is on the HCL for XS 7. The disks are a mix of drives that I had around my house. WD Reds and a WD green or two.
The drives shouldn't matter (I'd be really really surprised if it did).
I just checked you hardware as well and it is supported. I actually just installed XS7 on a desktop yesterday for a tiny project.
So I'm guessing it's a hardware problem of some sort.
Have you given XS6.5 a go on this system and see what happens?
No, I haven't tried 6.5 yet, only 7.
Give 6.5 a try and let us know if you have the same issue.
I will. I'll try to install 6.5, and then if that doesn't work, then I'll try to install a basic OS like Server 2012 and see if that works.
-
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
The RAID array should appear as a single drive and nothing that XS does should make a rebuild of the array needed. If that is happening, there is a deeper problem.
It does. It shows as a single 6 TB "drive"
Should not need to rebuild, then. If the underlying array is corrupting, then the issue is at the controller or disk level.
Any recommendations on what to check next on the controller and disks?
Most likely thing there is memory issues on the controller cache. See if you can get a diagnostic from Dell.
-
@scottalanmiller said in XenServer installation SR issue:
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
The RAID array should appear as a single drive and nothing that XS does should make a rebuild of the array needed. If that is happening, there is a deeper problem.
It does. It shows as a single 6 TB "drive"
Should not need to rebuild, then. If the underlying array is corrupting, then the issue is at the controller or disk level.
Any recommendations on what to check next on the controller and disks?
Most likely thing there is memory issues on the controller cache. See if you can get a diagnostic from Dell.
I wonder if the battery on the controller could be screwing with that. The other day, there was a message stating "W1228 Raid controller battery capacity < 24hr" It was gone the last time I checked this morning.
-
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
The RAID array should appear as a single drive and nothing that XS does should make a rebuild of the array needed. If that is happening, there is a deeper problem.
It does. It shows as a single 6 TB "drive"
Should not need to rebuild, then. If the underlying array is corrupting, then the issue is at the controller or disk level.
Any recommendations on what to check next on the controller and disks?
Most likely thing there is memory issues on the controller cache. See if you can get a diagnostic from Dell.
I wonder if the battery on the controller could be screwing with that. The other day, there was a message stating "W1228 Raid controller battery capacity < 24hr" It was gone the last time I checked this morning.
It's worth replacing if the system is sending alarms about it.
-
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
The RAID array should appear as a single drive and nothing that XS does should make a rebuild of the array needed. If that is happening, there is a deeper problem.
It does. It shows as a single 6 TB "drive"
Should not need to rebuild, then. If the underlying array is corrupting, then the issue is at the controller or disk level.
Any recommendations on what to check next on the controller and disks?
Most likely thing there is memory issues on the controller cache. See if you can get a diagnostic from Dell.
I wonder if the battery on the controller could be screwing with that. The other day, there was a message stating "W1228 Raid controller battery capacity < 24hr" It was gone the last time I checked this morning.
Should only be a problem if your power is not solid.
-
I'll run the built in LifeCycle diagnostics when I get home to see if it finds anything.
-
@scottalanmiller said in XenServer installation SR issue:
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
The RAID array should appear as a single drive and nothing that XS does should make a rebuild of the array needed. If that is happening, there is a deeper problem.
It does. It shows as a single 6 TB "drive"
Should not need to rebuild, then. If the underlying array is corrupting, then the issue is at the controller or disk level.
XS is actually installed on this array. If the RAID controller was corrupting the array, wouldn't this hose the XS installation as well and not make it bootable?
-
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
The RAID array should appear as a single drive and nothing that XS does should make a rebuild of the array needed. If that is happening, there is a deeper problem.
It does. It shows as a single 6 TB "drive"
Should not need to rebuild, then. If the underlying array is corrupting, then the issue is at the controller or disk level.
XS is actually installed on this array. If the RAID controller was corrupting the array, wouldn't this hose the XS installation as well and not make it bootable?
Most likely, but not definitely.
-
@fuznutz04
What does lvscan show you?
I had a similar error once because my lv was not active.
-
@BRRABill said in XenServer installation SR issue:
@fuznutz04
What does lvscan show you?
I had a similar error once because my lv was not active.
I'll check when I get back home tonight. Thanks.
-
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
@fuznutz04 said in XenServer installation SR issue:
@scottalanmiller said in XenServer installation SR issue:
The RAID array should appear as a single drive and nothing that XS does should make a rebuild of the array needed. If that is happening, there is a deeper problem.
It does. It shows as a single 6 TB "drive"
Should not need to rebuild, then. If the underlying array is corrupting, then the issue is at the controller or disk level.
XS is actually installed on this array. If the RAID controller was corrupting the array, wouldn't this hose the XS installation as well and not make it bootable?
If XS is installed on the array, you should not be running 'fsck /dev/sda'
What's the output of
parted -l /dev/sda -
@travisdh1
So here is what that command returns:[root@xenserver ~]# parted -l /dev/sda Model: DELL PERC H700 (scsi) Disk /dev/sda: 6000GB Sector size (logical/physical): 512B/512B Partition Table: gpt Disk Flags: pmbr_boot Number Start End Size File system Name Flags 5 1049kB 4296MB 4295MB ext3 2 4296MB 23.6GB 19.3GB 1 23.6GB 43.0GB 19.3GB ext3 4 43.0GB 43.5GB 537MB bios_grub, legacy_boot 6 43.5GB 44.6GB 1074MB linux-swap(v1) 3 44.6GB 6000GB 5956GB lvm Error: ff8e3b--dd7c--c3c4--3125--22569f5bbd77-0bff8e3b--dd7c--c3c4--3125--22569f5bbd77: unrecognised disk label Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/XSLocalEXT--0bff8e3b--dd7c--c3c4--3125--22569f5bbd77-0bff8e3b--dd7c--c3c4--3125--22569f5bbd77: 5955GB Sector size (logical/physical): 512B/512B Partition Table: unknown Disk Flags: -
@BRRABill said in XenServer installation SR issue:
@fuznutz04
What does lvscan show you?
I had a similar error once because my lv was not active.
[root@xenserver ~]# lvscan ACTIVE '/dev/XSLocalEXT-0bff8e3b-dd7c-c3c4-3125-22569f5bbd77/0bff8e3b-dd7c-c3c4-3125-22569f5bbd77' [5.42 TiB] inherit
