OK late to the thread. We use a cheap travel router for this purpose. GL.iNET GL-MT300N think we paid $25 for it. Supports up to 4 SSID's and can do VLAN's though we only use 1. We can actual do wifi to wifi bridging with it. We use it for these wifi Sapling clocks that need to connect to a pre-provided WPA2-PSK ssid for initial setup. This is the newest version: https://store.gl-inet.com/collections/travel-routers/products/gl-mt300n-v2-mini-smart-router Can get these on Amazon now for $25

@gjacobse said in UBNT: UniFi Controller Issue: Follow up, controller is running again under Win10. I’ll address a Linux system in the future at some point and move over so it can run full time. Worth it if you have a hypervisor running somewhere with enough extra resources for it - otherwise, in a home environment - not worth it.

@fateknollogee said in Unifi on Vultr: you 'has mad skillz?: I don't quite get your answer..does that mean it's too easy or it's not worth the effort? Basically yes, it is not worth the effort. You can setup apt to update automatically yourself quite trivially. The same for Let's Encrypt. Reskimming, I am not sure WTF he is doing with lighttpd I would need to look closer. But the scripting of the backup to a third party site is going to be totally custom to every install. This is way too complex to setup in a simple script. It works for him because everything is tied to the Google account.

Interestingly if I press download the URL is https://fw-download.ubnt.com/data/unifi-controller/242f-debian-v5.8.28_2batag-5.8.28-11052-5cedfbea2cca434a82f19db77124e9c6.deb

Youtube Video

@jaredbusch said in SIP Desk Phones Not Re-Registering with Main WAN's IP After WAN Fail-back: @scottalanmiller said in SIP Desk Phones Not Re-Registering with Main WAN's IP After WAN Fail-back: @taurex said in SIP Desk Phones Not Re-Registering with Main WAN's IP After WAN Fail-back: @jaredbusch Thanks for this link. I'll give it a try. I hope UBNT did not trim the CLI down too much on the USG. I now better understand why Edge series is still the prefered choice for deployment among many Especially now that UNMS is available, that's pretty slick. UNMS 0.12.0 (currenlty in alpha) will add the CLI to the web interface. That's very exciting. So much good stuff happening with UNMS.

@dbeato @JaredBusch thanks for the info. If I get time might give it a go over the weekend. Otherwise job for Monday morning

@jaredbusch said in Ubiquiti STUN Communication: @dbeato said in Ubiquiti STUN Communication: @jaredbusch said in Ubiquiti STUN Communication: @dbeato said in Ubiquiti STUN Communication: @jaredbusch said in Ubiquiti STUN Communication: @dbeato said in Ubiquiti STUN Communication: @jaredbusch said in Ubiquiti STUN Communication: @dbeato said in Ubiquiti STUN Communication: @mike-davis said in Ubiquiti STUN Communication: I'm hosting my unifi controller on vultr and I didn't have to make any port changes that I remember. So you didn't open any of those ports I listed? You do not normally need them. What don't you normally need them? 8080 and 8443 at a minimum correct? Correct. But I opened the 8880 and 8843 for HTTP and HTTPS for Guest Hotspot portal. Usually not needed for others but in this case it was needed. https://help.ubnt.com/hc/en-us/articles/115000871247-UniFi-Social-Media-Guest-Authentication#controller setup https://help.ubnt.com/hc/en-us/articles/115006809068-UniFi-Guest-Portal-Customization-Hotspot-System#comparison https://help.ubnt.com/hc/en-us/articles/205202640-UniFi-Guest-Portal-Promotional-URL-Automatic-Redirection With regards to STUN though, you believe is not needed then? Should not be as your controller is not behind NAT. There is not point to STUN unless NAT is involved. https://en.wikipedia.org/wiki/STUN How can it mark your post as the solution? Tell @scottalanmiller to do it because that is a glaring whole in this plugin. Has been reported, but unactioned for years now. Hey @scottalanmiller can you mark Jared's post with Wikipedia on it for the solution. I cannot for the life of me mark it as a solution.

@dbeato said in How to install the Ubiquiti UniFi Controller on Debian 9.1: @VoIP_n00b said in How to install the Ubiquiti UniFi Controller on Debian 9.1: So I got the Unifi Controller working with the same nginx config as the UNMS. Thanks again @JaredBusch Now how do I get my AP connected to the controller? Take a look at this https://help.ubnt.com/hc/en-us/articles/204909754-UniFi-Layer-3-methods-for-UAP-adoption-and-management#Section_5 DHCP option 43 - JB and I were just talking about what option was needed for a non UBNT firewall network to provide that to the APs.. thanks.

Thanks for posting this!

@JaredBusch not necessarily abnormal but surely a mix of 3 independent repos.

@JaredBusch said in Unifi - Migrate AP between controllers: @DustinB3403 said in Unifi - Migrate AP between controllers: @JaredBusch Yeah my question is odd, just was trying to determine what would be a reason for installing a new controller. It is an odd line of thinking, I know. I want to install a new controller, you just install the same version as existing, make a backup, restore backup, change DNS. done. I have done it more than one time over the years. This assumes you have a DNS server on your network that you control. If you have no local DNS server, this is a non issue, the AP will find the controller based on broadcast.

@JaredBusch said in Unifi AP refusing to upgrade: @Dashrender said in Unifi AP refusing to upgrade: @brianlittlejohn said in Unifi AP refusing to upgrade: Did yall notice that the new update has the ability to export and import individual sites instead of the entire config? didn't JB post about that a week or so ago? Nope. I must have just read it in a released then.

@dafyre said in UniFi controller will not start after upgrade to Ubuntu 16.04.01: Win! If I had realized that stable was not 5.0.X, I would have not changed to stable. Likely saving myself some steps.