Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s
-
Keep in mind I've had same issue on EVERY hypervisor from Citrix, VMWare and Hyper-V. I know hyper-v has its flags you need to turn off that are clearly documented to address the situation it has with nic's but were talking on the same SR lol. Not transferring across nic.
-
@black3dynamite not yet, I can try that again but I think my nic's are intel (not 100% sure), this is what I have done so far.
https://docs.microsoft.com/en-us/windows-server/storage/file-server/troubleshoot/slow-file-transfer
-
Have you tried disabling VMQ on the NIC Adapters in the VM? Some say this helps, others say it doesn't. I generally have good results with it.
-
I'll probably wait till everyone leaves and come in the morning early to double-check the BIOS. The disabling of the VMQ however, when I ran the command it didn't return that I had anything enabled....
I checked the Xen nic, and it doesn't have a listing in the advanced tab for the VMQ
-
@krisleslie said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
I'll probably wait till everyone leaves and come in the morning early to double-check the BIOS. The disabling of the VMQ however, when I ran the command it didn't return that I had anything enabled....
I checked the Xen nic, and it doesn't have a listing in the advanced tab for the VMQ
I figured it wouldn't, but I was putting it out there anyway.
If you look at the NIC status, what does it show the connected speed?
-
@krisleslie no one has mentioned it, but are you sure that you have GigE end to end? 10MB/s is the speed cap when you have a 100Mb/s network link somewhere.
-
You could also have a bad switch in the mix.... that was the case for someone around here recently.
-
@dafyre said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
ook at the NIC status, what does it show the connected speed?
1 Gb
-
@scottalanmiller can't be it, because sometimes I see it do 60 Mbps + like during OS install or if I happen to catch it.
-
Potential bad switch as in maybe one of the interfaces is bad? I think a long time ago me and scott thought about switching to 10 gb interconnects for each switch
-
Can't be the NIC (???) I'm doing like a file transfer from one folder to another on the same disk/vm of the vm that I'm running. When I tried last night to copy vm to vm yea after 10 hours only 1/3rd got done give or take an hour or so.
-
@krisleslie said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
Can't be the NIC (???) I'm doing like a file transfer from one folder to another on the same disk/vm of the vm that I'm running. When I tried last night to copy vm to vm yea after 10 hours only 1/3rd got done give or take an hour or so.
OK that takes the switch out of the situation.
-
@krisleslie said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
@dafyre said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
ook at the NIC status, what does it show the connected speed?
1 Gb
In the VM or at the Host?
-
As I'm running Crystal Disk Mark the speeds are so horrible I want to vomit.
-
@dafyre Both ( default server card)
-
@krisleslie said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
card
CrystalDiskMark 6.0.1 x64 (C) 2007-2018 hiyohiyo
Crystal Dew World : https://crystalmark.info/-
MB/s = 1,000,000 bytes/s [SATA/600 = 600,000,000 bytes/s]
-
KB = 1000 bytes, KiB = 1024 bytes
Sequential Read (Q= 32,T= 1) : 69.078 MB/s
Sequential Write (Q= 32,T= 1) : 101.986 MB/s
Random Read 4KiB (Q= 8,T=
: 9.545 MB/s [ 2330.3 IOPS]
Random Write 4KiB (Q= 8,T= : 13.363 MB/s [ 3262.5 IOPS]
Random Read 4KiB (Q= 32,T= 1) : 9.795 MB/s [ 2391.4 IOPS]
Random Write 4KiB (Q= 32,T= 1) : 13.832 MB/s [ 3377.0 IOPS]
Random Read 4KiB (Q= 1,T= 1) : 0.751 MB/s [ 183.3 IOPS]
Random Write 4KiB (Q= 1,T= 1) : 3.714 MB/s [ 906.7 IOPS]Test : 1024 MiB [C: 97.6% (1463.7/1499.7 GiB)] (x5) [Interval=5 sec]
Date : 2020/02/05 17:56:34
OS : Windows Server 2012 R2 Server Standard (full installation) [6.3 Build 9600] (x64)
-
-
On that note, I'm going to the nearest bottle.
-
@krisleslie said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
@scottalanmiller can't be it, because sometimes I see it do 60 Mbps + like during OS install or if I happen to catch it.
60Mb/s is a fraction of 10MB/s, though.
-
@krisleslie said in Using XCP-NG latest release, Windows 2019 Server VM file copies are pegged at 10 MB/s:
As I'm running Crystal Disk Mark the speeds are so horrible I want to vomit.
Drives having SMART issues, maybe?
-
Time to take a peak.
