Nextcloud Conflicts When Saving a File (Single User Scenario)
-
NextCloud 13 is quite a bit behind. We are on 15.0.2 now. Might be worth updating just to be sure that that does not address the issue on its own.
-
This might sound silly, but check the time on your machine and on the NextCloud server. Are they off from each other? Maybe one or the other actually is recording the time out of sync?
-
@SemperOSS said in Nextcloud Conflicts When Saving a File (Single User Scenario):
I am working on a very small software project and when I save a file (the only file in that directory), Nextcloud often seems to feel that the version stored on the server is newer than the version I just stored and makes the newest version a conflict file and reverts to the server version, which can be very damaging if I am not aware of it.
What task are you using NextCloud for with development? You aren't trying to store code in it, are you? NextCloud would not be a good replacement to a git repository, for example.
-
As a matter of troubleshooting... Check and make sure that the Client's time and the NextCloud server's time are set correctly.
-
@scottalanmiller & @dafyre: That was my first idea, but all the computers are within milliseconds of each other as best I can measure, thanks to NTP — and I do expect that Nextcloud can accept a clock difference that is in the same order of magnitude as the package latency over the network or even less.
-
@StrongBad I use Nextcloud to automatically save essential files on my computers, giving me seamless access to these files from my other computers. Very rarely are two computers turned on at the same time but it provides me with some convenience when I change from one computer to the other — and sometimes the web access to Nextcloud proves a life-saver ( well, not literally
) when I need access to files when I am out and about without access to my own laptop or for quickly sharing files.It is not used as a repository for my source code.
-
@JaredBusch & @scottalanmiller: Thank you for your response.
I'll probably have to throw some beefier hardware after it then as other suggestions I have received do not seem to apply to my case. I had hoped the RPis would be enough as I have managed to get rid of most of the old "big iron" and replaced it with RPis (web server, mail server, backup server, home server, security server, ...).
I had seen a post somewhere that the shift from SQLite to MariaDB should improve the stability for multi-user access and found it provided a slight improvement in performance as well — slightly surprising, I agree.
I know this is difficult, but do you have any sugestion as to the processor power and RAM needed for a stable Nextcloud installation with light use, mostly single-user access? I am seriously trying to avoid installing a "proper" server again for space and power consumption reasons. (The RPis are in fact installed in friend's basement as his internet connection has a fixed IP address.)
-
@scottalanmiller Thanks. I will try upgrading to the latest version.
-
@SemperOSS said in Nextcloud Conflicts When Saving a File (Single User Scenario):
@scottalanmiller Thanks. I will try upgrading to the latest version.
Worth a shot at the very least.
-
@SemperOSS said in Nextcloud Conflicts When Saving a File (Single User Scenario):
@scottalanmiller & @dafyre: That was my first idea, but all the computers are within milliseconds of each other as best I can measure, thanks to NTP — and I do expect that Nextcloud can accept a clock difference that is in the same order of magnitude as the package latency over the network or even less.
Yeah, was just thinking it might be an hour off or more.
-
@SemperOSS said in Nextcloud Conflicts When Saving a File (Single User Scenario):
@JaredBusch & @scottalanmiller: Thank you for your response.
I'll probably have to throw some beefier hardware after it then as other suggestions I have received do not seem to apply to my case. I had hoped the RPis would be enough as I have managed to get rid of most of the old "big iron" and replaced it with RPis (web server, mail server, backup server, home server, security server, ...).
I had seen a post somewhere that the shift from SQLite to MariaDB should improve the stability for multi-user access and found it provided a slight improvement in performance as well — slightly surprising, I agree.
I know this is difficult, but do you have any sugestion as to the processor power and RAM needed for a stable Nextcloud installation with light use, mostly single-user access? I am seriously trying to avoid installing a "proper" server again for space and power consumption reasons. (The RPis are in fact installed in friend's basement as his internet connection has a fixed IP address.)
Seems like a single small desktop device would have more computer power, and use less wall power, than using several small RPs, and be more flexible. Once you need more RPs than two or three in one place, they lose their value. If you only need one, that is different.
It doesn't need a lot, but 2GB of RAM minimum for sure. I'd do 3GB if possible, you don't want it swapping.
Minimum of 2 vCPU in a good VM on good hardware. Ours gets four.
-
@SemperOSS said in Nextcloud Conflicts When Saving a File (Single User Scenario):
I had seen a post somewhere that the shift from SQLite to MariaDB should improve the stability for multi-user access and found it provided a slight improvement in performance as well — slightly surprising, I agree.
Yes, but it does it through heavier utilization and thread competition, which might make the issue worse while making it feel faster. SQLite is "in thread" so can't have a race condition between the DB and the app.
-
@scottalanmiller said in Nextcloud Conflicts When Saving a File (Single User Scenario):
@SemperOSS said in Nextcloud Conflicts When Saving a File (Single User Scenario):
@JaredBusch & @scottalanmiller: Thank you for your response.
I'll probably have to throw some beefier hardware after it then as other suggestions I have received do not seem to apply to my case. I had hoped the RPis would be enough as I have managed to get rid of most of the old "big iron" and replaced it with RPis (web server, mail server, backup server, home server, security server, ...).
I had seen a post somewhere that the shift from SQLite to MariaDB should improve the stability for multi-user access and found it provided a slight improvement in performance as well — slightly surprising, I agree.
I know this is difficult, but do you have any sugestion as to the processor power and RAM needed for a stable Nextcloud installation with light use, mostly single-user access? I am seriously trying to avoid installing a "proper" server again for space and power consumption reasons. (The RPis are in fact installed in friend's basement as his internet connection has a fixed IP address.)
Seems like a single small desktop device would have more computer power, and use less wall power, than using several small RPs, and be more flexible. Once you need more RPs than two or three in one place, they lose their value. If you only need one, that is different.
It doesn't need a lot, but 2GB of RAM minimum for sure. I'd do 3GB if possible, you don't want it swapping.
Minimum of 2 vCPU in a good VM on good hardware. Ours gets four.
This is a client system with an active 50ish sync client users all day long.
Yeah it says ownCloud. THis was originally an ownCloud 7 VM on CentOS 7. It has been around a long ass time. Currently Nextcloud 14, no matter what @scottalanmiller says, NC 15 is not current as it is not in the stable release channel yet.
-
More stats from that system..
-
This is the sysem that I use for work.
We only have 6 active users. All use the Sync Client.
We never have any issues with conflict files.
