Static Router - EdgeRouter Lite

hobbit666

Pretty sure it ERL.
From a server at the WHS site if I traceroute to 10.0.1.220 it goes:-
Default Gateway(ERL) --> Draytek --> HO LAN

If I tracert to 172.20.0.X it goes
Default Gateway --> ISP Router --> ISP Router --> Timesout.

I've tried adding the 172.20.0 address to a static IP Via both 10.0.1.220 and Draytek (10.0.1.242) but that doesn't seem to work either.

scottalanmiller

Yup, sounds like a missing route on the ERL.

scottalanmiller

@hobbit666 said:

I've tried adding the 172.20.0 address to a static IP Via both 10.0.1.220 and Draytek (10.0.1.242) but that doesn't seem to work either.

It's a static route that is needed.

Dashrender

Have you done a route add command?

hobbit666

@Dashrender said:

Have you done a route add command?

On the ERL? I've tried adding via the web interface

scottalanmiller

What does the current routing table look like?

scottalanmiller

@Dashrender said:

Have you done a route add command?

I don't believe that there is a route add command on the ERL.

scottalanmiller

This is what adding a route looks like on VyOS:

set protocols static route 0.0.0.0/0 next-hop '190.66.11.49'

Dashrender

@scottalanmiller said:

@Dashrender said:

Have you done a route add command?

I don't believe that there is a route add command on the ERL.

Good to know, but you still knew what I was getting at.

dafyre

You will need to add static routes both on the ERL for EACH VLAN on the other end of the VPN that you want to access.

On your core switch at HO, you'll need to add a static route back to WHS...

Assume the following Networks:

WHS Subnet: 192.168.100.0/24
WHS ERL: 192.168.100.1/24
WHS VPN to HO: 192.168.5.158/24

HO Subnet: 192.168.5.0/24
HO Core Switch, VLAN 5: 192.168.5.1/24
HO Core Switch, VLAN 10: 192.168.10.1/24
HO Core Switch, VLAN 15: 192.168.15.1/24

On the WHS ERL, you'll need to add static routes:
192.168.5.0/24 via 192.168.5.158
192.168.10.0/24 via 192.168.5.158
192.168.15.0/24 via 192.168.5.158

On the HO Core switch, I believe you only have to add the following route:

192.168.100.0/24 via 192.168.5.158

Does that make sense?

Edit: The above is an idea only... Figure out the appropriate web or cli synax to make it happen.

Jason

Can the VPN not advertise the routes, so you don't have to do it statically on each client?

JaredBusch

@Jason said:

Can the VPN not advertise the routes, so you don't have to do it statically on each client?

Depends on the VPN technology in use. But yes it can be specified in the ERL GUI for IPSEC or command line for OpenVPN

hobbit666

0_1457365258208_basic whs route.png

So I've setup the draytek and ERL VPN adding the main IPs to the Local/Remote boxes.
As default from whs I can ping the Core switch and everything on the "HO LAN", but nothing on the VLAN15 side even the VLAN IP on the Cisco Switch.

I've tried a few ways of adding the static route to the ERL but nothing seems to help.

The draytek can ping all addresses.

hobbit666

Here is the ERL GUI

I have tried added the VLAN lan to that but still no go.

dafyre

@hobbit666 said:

So I've setup the draytek and ERL VPN adding the main IPs to the Local/Remote boxes.
As default from whs I can ping the Core switch and everything on the "HO LAN", but nothing on the VLAN15 side even the VLAN IP on the Cisco Switch.

I've tried a few ways of adding the static route to the ERL but nothing seems to help.

The draytek can ping all addresses.

Can we get a screenshot of the Static Routes page on the ERL, and the show route command on the Cisco?